Cord & Wire Tools

sort by:
  • 1
view:

Dash Protector

IP BDP1078

$64.00

Dash Protector provides protection for the a-pillar trim and the headliner while using our cut-out tools in addition to the dash.

Wire Grabber Pliers & Cutter

IP BNP516

$16.00

Used to pull cord or wire through urethane after insertion with the wirestarter. It has a ribbed nose that measures 1-1/2" long.

Centerstart™

IP CS789

$18.00

Our original Centerstart™ features a standard grip for wire insertion.

Protect-A-Dash™

IP CU1077

$30.00

This clear dash protector provides protection for the A-pillar trim and the headliner while using our cut-out tools.

Wire Guide

IP DGE100

$36.00

The wire guide’s long, narrow shaft protects the dash and interior moldings from being damaged. It can also be used on the outside where the urethane is far below the dash but above the bottom edge.

To use, run the wire through the hole at the end of the tool. Then, with the wire on the round side of the tool, attach the end of the wire in the hole midway up the tool, locking it in place with the set screw. Move the tool on the inside of the vehicle, a few inches at a time, while the person on the outside follows doing the cutting. The smooth metal will move under the moldings and along the dash and prevent damage.

Pistol Grip Centerstart™

IP FG1129

$18.00

Pistol Grip Centerstart™ features an ergonomic handle and a hole designed to accept both cord and wire. 

WireGuard™

IP GWH366

$28.00

Provides protection for the A-pillar trim and the headliner while using our cord and wire cut-out tools.

Invented by: Tim Slaughenhaupt 

Clear Headliner Protector

IP HP564

$18.00

Provides protection for the A-pillar trim and the headliner while using our cord and wire cut-out tools.

 

Invented by: Gilbert Gutierrez & Jason Horne

T-Handle Centerstart™

IP JN1130

$16.00

The T-Handle Centerstart™ is a popular wire insertion tool for a wire that can also be used in conjunction with the WL1135 wire loops for a cord.

Loop Wire Starter

IP LS1134

$24.00

For use on those vehicles when you insert the wire starter and there is not enough room to see the hole of the wire starter (ie. the Jeep Wrangler). Also, works great for starting cord that can be difficult to secure on a conventional wire starter.

 

Comes with 5 extra wire loops.

 
Invented by: Eric Asbery & Gilbert Gutierrez

Venom™

IP WDD167

$37.00

Equalizer® Venom™ is a cord and wire dispensing device used in conjunction with Raptor™,  Viper™, Python™, and Cobra™ removal systems.

Includes one roll of STL166 wire.

Wirestarter™ • 4"

IP WS782

$8.00

Wirestarter™ is a hollow stainless steel tube with grip used to channel cord and wire through urethane. 

To use, push the tube through the urethane, insert the wire through the tube, then pull Wirestarter™ out, leaving the wire in. Be sure to lay the flat side of the aluminum handle against the glass and then use your thumb or fingers to push the tube through the urethane. Also, be sure to concentrate your force directly in line with the tube. Failure to follow these directions may result in the tube bending.

Wirestarter™ • 8"

IP WS782P

$8.00

Wirestarter™ is a hollow stainless steel tube with grip used to channel cord and wire through urethane. 

To use, push the tube through the urethane, insert the wire through the tube, then pull Wirestarter™ out, leaving the wire in. Be sure to lay the flat side of the aluminum handle against the glass and then use your thumb or fingers to push the tube through the urethane. Also, be sure to concentrate your force directly in line with the tube. Failure to follow these directions may result in the tube bending.

Mini Anchor Cup

IP MAC1125

$30.00

The mini anchor secures the end of the cord and wire allowing completion of the finishing cut. Measures 2-1/8” in diameter (the anchor tab adding an extra 1/2” to that) and 1-1/2” H when the suction cup is engaged. 


Invented by: Jason Horne

  • 1