Mouldings & Clips

sort by:
view:

Gold Glass Group 75' Spool

IP T107B

$74.00

Gold Glass Group Mouldings do not shrink or discolor over time, never crimp around corners, always lay flush against the vehicle, never need a heat gun to install, and fit both thick windshields and thin tempered parts. A thin layer of butyl is in the channel of each moulding. When the moulding is pushed onto the glass, the butyl adheres to the edge of the glass and the moulding will not come off. T110 It is intended to replace push-in “Christmas Tree” mouldings. The great thing about this moulding is it has an adhesive under the part that goes against the vehicle. This adhesive sticks to the vehicle and holds the moulding in place while the urethane cures. The adhesive assures a perfect bond and the cured urethane holds it permanently in place.

1" Gold Glass Group 75' Spool

IP T108B

$74.00

In the past, you could spend more time saving the molding than you spent removing and replacing the windshield. There were many reasons for saving a molding, but the most common reason was that it was difficult to stock all the different moldings. Insurance companies realize that you cannot always save the molding when replacing a windshield. For this reason, they now pay for a new molding when the old one cannot be saved. old Glass Group has solved the first problem. You no longer need to stock dozens of different moldings. You can now reduce your inventory with universal moldings. Four moldings equal over four hundred applications. old Glass Group moldings do not shrink or discolor over time, never crimp around corners, always lay flush against the vehicle, never need a heat gun to install, and fit both thick windshields and thin tempered parts. A thin layer of butyl is made into the channel of each molding. When the molding is pushed onto the glass the butyl adheres to the edge of the glass and the molding will not come off. You will not find T110 listed on the chart at right. They are both intended to replace push-in “Christmas Tree” moldings. The great thing about these moldings is there is adhesive under the part that goes against the vehicle. This adhesive sticks to the vehicle and holds the molding in place while the urethane cures. The adhesive assures a perfect bond and the cured urethane holds it permanently in place.

Channel Mouldings with Butyl 1"

IP ET108B

$52.00

In addition to extremely high-quality moldings, Gold Glass Group also offers economy moldings. Do not let the word economy fool you. When Gold uses the word economy, it takes on a whole new meaning. These are high-quality moldings and, when compared to most competitors, they would be considered the highest-quality available.

This item is oversized and will have extra shipping charges.

Rubber Underside Moulding

IP ET204

$73.00

An EPDM rubber underside molding. This molding profile can be used in applications with a shallow pinchweld and a wider distance from the edge of the glass.

100' spool.

Tight-Radius Underside Moulding • 100'

IP ET202

$73.00

The ET202 is specifically designed to replace these damaged mouldings on quarter and back glasses that have extremely tight-radius corners.

Each spool is 100 feet.

Tight-Radius Underside Moulding • 9/32"

IP ET203

$73.00

The ET203 is specifically designed to replace these damaged moldings on quarter and back glasses that have extremely tight-radius corners.

The spool is 100 feet long.

Underside Moulding

IP ET201

$73.00

There are many glasses on the market that cannot be removed without destroying the moulding. Now you can remove and replace those glasses with our Underside Moulding. The ET201 has an adhesive strip that lets you attach it to the bottom edge of the glass, just like the original. You then reinstall the glass and the moulding makes a good-looking seal between the glass and the body.

90' Spool.

Equalizer® Hot Pocket

IP MHP139

$73.00

A portable option to keeping all urethane warm and easy to dispense and mouldings pliable. Heats up to 105°F and holds up to two boxes of moulding or 18+, 20oz. sausage pack urethane tubes. 

Draws only 2.8 amps of 12-Volt electricity and has a self protecting design that will not let it draw more than 5 amps. 12-Volt Urethane or Moulding Heater.

Made of Ballistic nylon.

Equalizer HeatWave™ 120 Volt Heat Gun

IP HGS353

$163.00

Perfect for reshaping moldings, drying pinchwelds, or warming glass and pinchwelds. This compact, lightweight, easy to use heat gun is perfect for dozens of shop uses. With temperature settings of 570° F and 1050° F and an airflow of 15 CFM at 3650 FPM, the HeatWave™ will handle a wide range of heating requirements where high and low heat is required. The HeatWave™ features an ergonomically designed Lexan® housing that is lightweight. It has an oil resistant, grounded neoprene 3-wire cord set. It has a built-in hand and switch guard with a double protected element housing and a wrap-around air intake. The air intake allows the gun to draw in the air while in the upright position. HeatWave™ has a hanging loop for easy storage and a built-in stand.

Made in the USA.

Heavy Duty Heat Gun

IP FV1128

$228.00

Professional, heavy duty, industrial quality heat gun.

Our professional heat gun will heat up to 1000° Fahrenheit and has a huge airflow of 23 cubic feet per minute. The perfect tool for those rainy/snowy days when you really need to dry out the area around a windshield or back glass, or heat those moldings. It has a powerful high-speed motor, a sturdy die-cast housing, and an adjustable non-slip stand. The non-slip stand has a rubber backing so you can set it on the vehicle without worrying about damage to the paint. The switch is wired so it will blow without the heating element being turned on. When finishing a job you put the switch on the blow cycle and it will cool the heating element. This feature can add hundreds of hours to the life of the heating element. A friction-style air flow adjustment allows you to increase or decrease the heat produced by the heat gun.

Made in the USA.

MegaRaptor™ Standard Moulding Maker

IP MCA265

$30.00

Make precise angle cuts into mouldings with MegaRaptor™.

The lower jaw has cast-in numbers and lines to show you the angle you are cutting. Place your universal moulding on the lower jaw of the moulding cutters and squeeze the handle.  Its replaceable utility knife blade cuts the moulding straight, smooth and at the proper angle. You can replace the cutting blade by removing the two screws.

Uses standard utility knife blades (UKB498).

Zap-A-Gap Super Fast Setting Plastic Glue

IP AA1003

$7.00

These days there seem to be more plastic parts on a vehicle than there are metal parts. It is inevitable that when removing parts to replace a glass, you will break some of these pieces of plastic. Often the broken part will need to be replaced, but you can make a temporary repair by gluing it back together. Simply put a small drop of Zap-A-Gap™ on the plastic parts and press them back together. In a few seconds, the glue is dry and the pieces are bonded.

Made in the USA.

The bottle contains 0.5 fluid ounces.

Zip Kicker™

IP AB1005

$9.00

Zip Kicker™ Accelerates glue drying and help fill holes.

Sometimes just gluing the part is not enough. You need to build up an excess amount of glue on the surface to give the bond more strength. While Zap-A-Gap™ dries quickly in small amounts, it takes a long time for large amounts to dry. This is when you need Zip Kicker™, an accelerating, sprayable liquid that causes the glue to dry immediately. It is also useful when small amounts of the plastic have disappeared. The Zap-A-Gap™ can be used to fill the opening and then dried immediately with Zip Kicker™ to form an instant patch. The bottle contains 2 fluid ounces.

Made in the USA.

Black Moulding Adhesive

IP BMG466

$8.00

An easy way to save money on OEM mouldings is to create your own using a universal moulding. When making mouldings that are mitered together or that meet at the bottom of the glass, you'll need an adhesive that permanently holds the moulding together.

Our Moulding Adhesive is super-strong and weather-resistant. It only takes a small drop to glue the moulding ends together, so each bottle has enough adhesive for hundreds of mouldings.

MouldingMaker™ Adhesive

IP UMA297

$7.00

If you are making moldings that are mitered together at the corners, or moldings that go all the way around a glass and join together at the bottom, then you need an adhesive that will permanently hold the molding together. Equalizer® MouldingMaker™ adhesive is a permanent, colorless adhesive that is specially formulated to join moldings.